Singapore 20-11-2018
The Europium chalcogenide (EuX) thin films have been deposited bare glass substrates by chemically with spray pyrolysis technique at different substrate temperatures, in aqueous medium. The films synthesized were studied morphologically. The effect of substrate temperature on morphological properties has been investigated. The XRD studies reveal that, the films are polycrystalline in nature and the deposited material was europium sulphide. The SEM analysis conforms the formation of small grains on overall substrate.
Keywords - EuX,Spray Pyrolysis, SEM, EDAX
This paper details on the sensor nodes (SNs) for aircraft surface sensing, especially operating them on the far-field wireless powering, also known as RF powering. The SNs includes RF energy harvesting circuit, harvesting voltage booster, data link transceiver and sensor interface circuits. Modelling & Simulation of the most critical block in the link, RF-DC converter is described. The RF-DC converter exhibits more than 25% efficiency even with the input power levels less than -18dBm. Thus, without exceeding the FCC emission limits, the base station is able to wirelessly power the SNs up to 10 m range.
Keywords - Battery-less sensor nodes, Wireless charging, Far filed RF energy harvesting
In this work, the novel concept of non-uniform temperature district heating system with decentralized heat pumps and stand-alone heat storage units is proposed. In this system, the temperature within the transmission pipeline is always at the ultra-low level and the heat pumps will increase the temperature to 70oC during a short period a day to provide the domestic hot water need of the consumers. Heat pumps are sized in neighborhood scale, and each heat pump is assigned for a few neighborhoods. By such a design, a strong synergy between the heat and electricity sectors is made, the rate of heat loss is minimal, a high potential for employing low-grade renewable sources is made, and the legionella risk is absolutely zero. These features are all the important characteristics of the smart energy systems. The system is designed and analyzed for a case study. It is demonstrated that the proposed system shows the best performance compared to any other district heating solution.
Keywords - District heating; Non-uniform supply temperature; Decentralized heat pump, Stratified storage tank.
This paper proposes an adaptive spin orbit torque non-volatile flip flop (SOT-NVFF) design. The proposed design offers two schemes of operation to ensure data security. Firstly, the nominal scheme at which the data is stored on the SOT-MTJs only when an external enable signal is initiated. A second scheme is automatically activated when supply instability is detected. This scheme stores the data every clock cycle, which aids in achieving higher data security. The control circuit that switches between the two schemes is also presented in this paper. Furthermore, the proposed NVFF only requires four overhead (OH) transistors, which results in more compact design compared to its counterparts in the literature. It also utilizes a series writing technique that aids in achieving at least 21% lower backup energy compared to others. Further study shows that the proposed NVFF offers better VDD scalability. It is also robustandstable even with process and device variations.
Keywords - SOT, MTJ, NVL, Power Gating
A novel hybrid sensing scheme with enhanced reliability for Spin-Transfer-Torque MRAM (STT-MRAM) was proposed. The sensing scheme performs a mid-point reference read and a grey zone (GZ) cell detection process where a STT-MRAM cell is determined if it falls within the resistance overlapping zone. Based on the detection outcome, weak cells within the GZ that are highly susceptible to read error will undergo a second process variation tolerant non-destructive self-reference sensing (NSRS). Monte-Carlo simulation across process variation and read currents corners demonstrate the enhanced read reliability in the proposed sensing scheme with an average of 44.7%, 92.2% and 95.3% improvement of bit error rate (BER) over the conventional mid-point reference sensing technique with 5%, 8% and 10% standard deviation of the MTJ diameter, respectively. With an extended GZ detection range, the respective BER can be further reduced by 91.3%, 87.7% and 82.3%.
Index Terms - Bit Error Rate, Hybrid Sensing, Monte-Carlo Process Variation, Resistance Overlapping, Stt-Mram, Self-Reference Sensing.
This paper exploits circuit techniques to realize a power-gated MRAM with the instant-on characteristic. Each block in a large-capacity MRAM is gated by a separate power transistor, allowing it to be fully turned on after only 1.3 ns. The whole MRAM memory can always be put in sleep mode, except the selected block. This eliminates the need for access pattern prediction as well as the requirement that the MRAM must be in idle for a significant of time before it is put in sleep or deep sleep mode. Our simulation shows that even in the worst-case-scenario, 86% of leakage current is saved. Our proposed scheme’s implementation is straight forward and incurs less than 0.5% area overhead, including power transistors and control circuits.
Index Terms - MRAM, low-power, low-leakage, normally-off system
High-energy environmental radiation particles may affect the operational reliability of a System on Chip (SOC). These particles may cause errors in the combinational logic, sequential logic, and even in the clock network. In the latter, they appear as clock glitches that propagate, and eventually, incorrectly latch all the sequential circuits, such as flip-flops and latches attached to the clock node concerned. The impact on chip functionality is usually fatal. In this work, we propose a low-cost adaptive clock glitch removal circuitry for radiation-resilient clock networks. The proposed technique can be adjusted based on the actual clock glitch profile, to ensure that the error in the clock network is removed, while the impact on the clock signal itself is minimized. It is fully synthesizable, and can thus be incorporated in a conventional digital flow.
Index Terms - Radiation-Resilient, Clock Network, SEU.
An efficient, high frequency power management unit (PMU) is reported in this paper. The PMU comprises of a front-end buck converter and a second-stage Low Drop-Out Regulator (LDO). The PMU converts 2.5V from battery power supply to a 1.2V output, with 1A load current capability. The IC is fabricated using 130nm CMOS technology node and occupies an active area of 1.6x1.6mm2. The tested chip has an average end-to-end efficiency of 73 % and is suitable for powering on-chip loads.
Keywords - Power management; DC-DC Converter; Buck Converter; LDO
A stable and efficient Low-Dropout Regulator (LDO) is reported in this paper, with 1A output current capability. The LDO converts a 1.5V input to 1.2V output. It uses a two-stage amplifier to achieve large DC gain. An output capacitor is used to provide the high PSRR. Compensation capacitor is added to ensure stability. The IC is fabricated using 130nm CMOS technology node and the measurement results are presented. Line regulation and load regulation of LDO are measured to be 6.4mV/V and 5mV/A respectively.
Keywords - LDO; Efficiency; Power Management; Drop-out; Regulator
Performance per Watt has become increasingly important metric for microprocessors used in today’s mobile devices. Dynamic voltage frequency scaling (DVFS) is widely used approach to improve on the performance/Watt. In this paper, integrated voltage regulator (IVR) type multiphase buck converter switching at 100 MHz providing a maximum load current of 2.0 A is presented, useful in DVFS applications. To realize such high switching frequency converter, all the components including the low-pass filter passives namely inductor and capacitor where made on-chip. In-house magnetic core based inductor for higher inductive density and MOSFET based capacitor are used to realize ASIC with no components on board. Thus, eliminating bottlenecks arising from bond-wire parasitic restricting the response time to few 10s of µs range. The converter output voltage settles within 5-7 clock cycles roughly around 50-70 ns timescale for a step load current change of ∆IL = 1.0 A. The converter output ripple is also curtailed to few 10s of mV mainly through ripple cancellation using multiphase, plus lower inductor current ripple on account of operating at high switching frequency.
Keywords - Multiphase Buck Converter, Switching Mode Power Supply, Integrated Voltage Regulator, Dynamic Voltage Frequency Scaling, Voltage-mode Controller.
The neuromorphic computing requires a very-large-scale integration system to implement the spiking neural network. However, traditional bus topology is not suitable for network interconnection due to its low scalability. To achieve scalability, network-on-chip is applied in the neuromorphic computing. The routing algorithms used by the network-on-chip affect the networks performance.Unlike the wormhole routing model, which has more than one flit in each packet, the packet of the neuromorphic computing only contains one flit. However, performance analysis of different routing algorithms completed in previous works is based on packets containing multiple flits.In this paper, the performance of the XY, odd-even, and dynamically adaptive and deterministic routing algorithms (DYAD)are analyzed for the neuromorphic computing. The simulation is carried out on the NIRGAM simulator.
Index Terms - Network-on-chip, neuromorphic computing, XY routing algorithm, odd-even routing algorithm, DYAD routing algorithm
This paper proposes a robust and flexible controller for multi-channel neuromuscular current stimulator chip. The design supports various modes of operations, including housekeeping modes, debugging modes and finally stimulation control modes. For debugging, it is able to monitor internal operating nodes and long-term data transmission bit error rates. For simulation control, it is capable of storing pre-defined stimulation patterns and controls eight individual channels simultaneously. The design was implemented and verified using standard 0.18 um/ 1.8 V CMOS process. Finally it was integrated in a neuromuscular SoC with completed analog front-end and wireless power harvesting circuit.
Hardware implementation of spiking neural networks (SNN) has been the focus of many prior works [1-3] due to its relatively low power consumption.When building SNNs, it is typical to consider various forms of neuron models, as it is the key computational unit in the neural network.In this paper, various different digital neuron models will be introduced, followed by an analysis done on each of them, along with comparisons pertaining a series of different features they contain. Three methods of implementing LLIF on hardware will be looked at and comparisons will be made towards their respective components.
Index Terms - Spiking Neuron Model, Spiking Neural Network Hardware, Digital Neuron Circuits.
This paperpresents a 5.8 GHz fractional-N synthesizer that is used for wireless transceiver applications in 55nm CMOS process. The synthesizer could cover 5.8GHz frequency band with quadrature I/Q output. Simulations show that the phase noise (PN)@11.6GHzof the synthesizer is -80dBc/Hz, -95dBc/Hz and -105dBc/Hz with frequency offsets of 50kHz, 100kHz and 1MHz respectively. The die area of the proposed synthesizer is 0.6mm X 0.7mm. Thecurrent consumption of the synthesizer is 15mA with 1.2V supply voltage.
Keywords - CMOS, PLL, FRACTIONAL-N Synthesizer
This paper presents a I /Q up mixer with a low pass filter (LPF) for 5.8 GHz transmitter applicationsin 55nm CMOS process. The up mixer could cover the 5.8GHz frequency band and support π/4-QPSK modulation. The data rate could be up to 4096kbps.
Keywords: CMOS, DSRC, Transmitter, DAC, LPF, Mixer,
Diabetic Foot Ulcer (DFU) is a complication of diabetes; this causes impaired mobility and even death. Higher rate of DFU occurrence adds huge burden on the healthcare system and billions are spent healing the wound. There is a need for reliably measuring dynamic foot pressure so that the users who are at a risk of DFU can be given feedback in real time to help them avoid DFU. We are developing a dynamic foot pressure measurement system in house to provide full coverage of risk foot areas and can measure up to 100 channels of dynamic pressure. In this paper we present a miniature 12 channel dynamic foot pressure measurement system consisting of an analog front end, an MCU based data acquisition moduleand a sensorized sock. This system can measure, analyze and store dynamic foot pressure data and feedback to the user in real time through on board aural and visual indicators. It can also optionally push the collected data to the back end server through a wireless link. Sensorized sock was fabricated by embedding off the shelf Force Sensitive Resistor (FSR) elements on the sock and wired up using conductive threads to form an array. Non-Inverting Op-Amp Circuit on board analog front end converts the resistance variations of the pressure sensor into avoltage which is then converted to digital using an on chip ADC of the MCU. MCU further analyzes the data and activates alarms when the detected pressure values exceed preset threshold values. The pressure measurement range of this systemis 100– 600Kpa with targeted accuracy of +/-2% and the scanning rate is 10 fps.
Keywords - Diabetic Foot Ulcer, Dynamic Foot Pressure, Sensorized Sock, Force Sensitive Resistor (FSR), Op-Amp.
Plato showed in his famous work “The Republic” which waswritten before Christ about Socrates dialogues.S ocrates points out the human tendency to be corrupted by power, and he concludes that the ruling should be left to philosophers, who are the most just and therefore least susceptible to corruption. Corruption has been existing for a long time, and it is a global phenomenon. Corruption is generally linked with essence activities of the public authorities and especially with the monopolistic discretionary power of the state. In Vietnam, the subject of anti-corruption or anti-bribery is mainly governed by the Anti-Corruption Law and the Penal Code. At the provincial level, according to The Viet Nam Provincial Governance and Public Administration Performance Index - PAPI reports which is the most massive time-series national governance and public administration performance monitoring tool in Viet Nam exclusively based on citizen’s experiences, the score of the Control of Corruption varied from 4,31 to 7,14 among 63 provinces in Vietnam in 2016. Why did the control of corruption vary among provinces? This paper aims to find the reasons which make the control of corruption index varied among 63 provinces in Vietnam, primarily concentrates on the interaction between corruption and public budget; between corruption and some socio-economic characteristics. The exciting result is there is no relationship between the control of corruption and public budget. Only Gross Regional Domestic Product – GRDP has a positive effect on the control corruption while poverty rate, Average Income, Ethnic Minority, and unemployment rate have a negative impact.
Keywords - Control of corruption, corruption, public budget, social-economic index, provincial level, Vietnam
This study investigates the viewpoints of higher education managers, faculty members and students on the impact of ACBSP (Accreditation Council for Business Schools and Programs) on student learning and performance. These views are explored through a case study approach from FPT University, which is one of the largest and most accredited private universities in Vietnam and has been approved a candidacy for ACBSP Accreditation since 2016. The study’s results suggest that accreditation influences most of the university’s management activities, including institution’s academic programs, teaching activities and student learning. We argue the influence of accreditation contributes significantly to encourage continuous quality improvement and exceed students’ expectations. Recommendations for improvement in the use of ACBSP Accreditation results are proposed.
Keywords - ACBSP Accreditation, impact, student learning outcomes, higher education
This study would be conducted in two phases. First, researcher use Awareness Pyramid Model to evaluate the current situation of brand awareness about FPT University. The focus group interviewees would be formed by students who are potential students to FPT Univerisity. Those students did not have knowledge about accredictation, before attending the interview, researcher had tested their knowledge about accredictitation by using open-ended questions. At the second phase, the researcher would issue the survey questionairs together with information about accreditation and FPT University activities in those accredictation organizations. The surveyees are required to read the information before answering the survey, this step to make sure that surveyees have knowledge about accreditation and FPT university. The survey would be conducted to more than 300 respondense. Then, the researcher would test the begining hypothesis: accredictation information would increase the brand awareness of FPT University. This hypothesis would be accepted if the indetification level of awareness pyramid at the second phase is higher than the first phase, otherwise, rejected. This research simply finds out whether the information about accreditation would affect to the brand awareness of the institue or not. This findings would be helpful for the institue’ managers, marketers to invest more in accredictation for not only academic quality improvement but also brand awareness.
.
Keywords - Accreditation, Impact, Brand Awareness, Higher Education, University, Fpt University, Awareness Pyramid Model.
This is an exploratory research on FPT University students in international program. The research would be both secondary and primary, aiming to list out the favourable website, platforms that most of the student surveyees are using. Moreover, the study will also finds out the factors that make those websites getting more visiting by the students for the self-learning. The author plans to list at least 50 websites, those are avaiblable online, collecting their page comment and review to evaluate their service quality. For primary research, the author would do a survey of 300 samples who are software engineer students of FPT university, experienced at least two self-learning service websites. This research would be firstly, helpful for students and lecturers because it provides many in-deep and useful information for their preference in making decision. Second, the research is helpful for web-designers who are providing online self-llearning service, to enhance their service quality by understanding what are expected by the students. Finally, it is helpful for all of the readers to have an overview of the current situation in student’s self-learning behavior.
Keyword - web design, students, self-learning, FPT University, service, online service quality.
It has been 40 years since the research of Second language acquisitionstarted growing as an independent field of study, and the concept of “language performance” has often been used in studying second language acquisition. According toChomsky, a distinction is often made between competence and performance when studying language. In the case of second language acquisition, this concept means using grammar in the process of comprehension and production of language for thecommunicators (David Krystal2004), in other words, language performance is the actual use students of language (Richards 2000). This studyusing experiments and literature as the main approaches for research and using the theory of second language acquisition asthe main reference theory. When student completed homework system developed by teacher and according to the schedule of syllabus, they can improve their language performance. The author measureseffectiveness of homework system through the HSK 1 level exam at the end of the semester. Afterdescribing theresults, the author proceeds to analyze the reasons influencing student’s language performance by analyzing of the data collected during the research. Based on the results studied, we analyze and proposesome main explanationsfor the findings of the experiment.
Keywords - Chinese Language Acquisition; Performance; Accuracy; Complexity; Diversity; HSK; Homework system
In this paper we preset a multi-phase Voltage Controlled Oscillator (VCO) that uses a replica biasing circuit to ensure that the output swing of the VCO is uniformly distributed across a common mode voltage. Since the VCO output swing is regulated across the common mode voltage, the output phases are uniformly distributed. The output phases of the VCO can be used for generating multi-phase switching outputs in voltage regulators. The frequency of oscillation can be controlled using the current source. Proposed scheme was implemented using 0.18m CMOS technology. It can be seen from the simulation results that the proposed scheme has a wide tuning range of 1MHz-90MHz and can produce 4 uniform phases.
Index Terms - High frequency switching regulators, muli-phase output, replica biasing, VCOs.
This paper describes in detail, a data acquisition system and the measurement results for pipeline leak detection. The data acquisition system hasa software platform to perform signal analytics; hardware for acquiring sensor data and perform signal processing; and a hydrophone sensor for acquiring acoustic signals. The data acquisition system was used to acquire data from packaged hydrophone sensors which were deployed to monitor the acoustic ina water pipeline under a laboratory condition. Data analysis using both transient and spectral interrogation methods showed thatfrom captured data, it was possible to clearly identify water flow disturbances due to leakages.
Keywords - Data Acquisition, Signal processing, background noise cancellation, water leak, acoustic.