Bangkok, Thailand, 04-04-2015
ISBN 978-93-82702-89-4
We consider a retailer who is facing uncertain supply as well as demand and who has to make a stocking decision for a given selling period. If demand exceeds supply, the unmet demand is lost and if the opposite happens, any units left can be salvaged at a reduce value. When demand is unmet, there is lost goodwill as well as the risk of loss of future business. In literature this problem is considered a variant of newsvendor problem. Retailers prefer using service level rather than the shortage penalty to determine the tradeoff between revenue and the loss of goodwill or loss of future business. In this paper, we develop a procedure for finding the optimal policy for the retailer assuming general distributions for the yield as well as demand. The goal is to maximize expected revenue given the cycle service level. The results have important implications for a retailer when a portion of the inventory may be lost due to variety of factors including failure to meet quality standards, theft or perishability.
Keywords- Data Mining, Intelligent Systems, Financial Risk, Early Warning.
Investigations were undertaken to study arsenic (As) removal from arsenic groundwater using fly ash (FA), bottom ash (BA), and bentonite clay (BC). Toxicity characteristic leaching procedure (TCLP) reveals that fly ash, bottom ash, and bentonite claycontained heavy metals such as Manganese (Mn), Copper (Cu), Zinc (Zn), Arsenic (As), and lead (Pb). Continuous column test with fly ash, bottom ash, and bentonite clay showed negligible heavy metal leach-out at neutral pH, except for Zn leached from bentonite clay.Column arsenic removal studies reveals order of arsenic removal using three ratios of reactive material mixturesas ratio of 60% BA, 20% FA, 20% BC mixtures> ratio of 80% BA, 10% FA, 10% BC mixtures> ratio of 100% BA. Removal of arsenic is attributed mainly to sorption due to negatively charged surface of fly ash, bottom ash, and bentonite clay.
Keywords- Arsenic Removal, Permeable Reactive Barrier, Coal Fly Ash, Coal Bottom Ash, Bentonite Clay.
Environmental pollution has become a world-wide problem. The growth of industrialization leads to the rise of wastewater produced from various industries and the pollution load on the environment is increasing. The treatment and disposal of industrial wastewater is becoming a challenging problem for developing countries. Industrial wastewater is very complex and the main concerning contaminants are bacteria, parasites and viruses, inorganic and organic pollutants. The main purpose of this research is to develop the industrial wastewater treatment technology in Myanmar. Ionizing radiation has more advantages over the chemical or biological treatment process of industrial wastewater. Very few amount of chemical reagents as initiators and Co-60 gamma radiation source were used to reduce massive load microbial count (~1010CFU/ml), biochemical oxygen demand (BOD ~7000 mg/l) and chemical oxygen demand (COD~30000 mg/l) to safety disposed level in this research. The sample used in this research was combined wastewater from distilleries, sugar factories, candy factories and textile factories. The collected sample was pre-treated with some chemical process and then was to be irradiated into the gamma chamber at a dose of 1 kGy to 18 kGy. Effects of gamma radiation on industrial wastewater and sludge were determined by the reduction rate of total microbial counts, COD and BOD. The optimum dose for the disinfection of bacteria and degradation of organic and inorganic pollutants were obtained. The irradiation dose of 6 kGy was adequate for the disinfection of wastewater and the reduction of COD and BOD to the permissible level was achieved at 18 kGy irradiation dose.
Keywords- Industrial Wastewater, Ionization Radiation, Biochemical Oxygen Demand (BOD), Chemical Oxygen Demand (COD), Microbial Counts, Gamma Radiation, Organic Pollutants
Increasing world population is one factor which causes the growing vegetable oil production in the world. The most produced vegetable oils in the world are such as cottonseed oil, palm oil, rapeseed oil, soybean oil, sunflower oil. In year 2012, palm oil was the most produced vegetable oil with world production by 53,3 million tons. Indonesia is the most producer of crude palm oil (CPO) in the world with production by 26,9 million tons in 2012. By palm oil industry biomass will be generated in plantation and at the palm oil mill. Empty fruit bunch of oil palm (EFB) is one of biomass which is generated at palm oil mill. The amount of EFB and the production of CPO is proportional. It means there were about 26,9 million tons of EFB available in 2012 in Indonesia or 53,3 million tons in the world. Nowadays, only small amount of EFB would be utilized for different purposes such as as animal feed, compost, briquettes, particle boards. From 100% EFB can be gained about 50% fibers of EFB. After fiberizing stage the EFB to be fibers, followed by fibers screening stage, the fibers will be raw material which can be processed furthermore to be prepregs and finally to be composites. In this research the natural binding agent of starch of potato will be used. With composition of 1:1 between the fibers and the binding agent. They will be mixed and prepregs will be produced. At next, the prepregs will be hot pressed with temperature by 180 0C, pressure by 40 bar and press duration by 15 munites to be enviromental friendly composites. According to standard DIN 53 457 (the 3 points bending) the material have strengthness about 7 GPa. 5 layers of these composites were prepared for ballistic test at distances of 5, 10 and 15 m and they showed good results. It is possible to implement environmental friendly composites from fibers of oil palm empty fruit bunch mixed with starch binding agent from potato to be bullet proof components for armoured vehicles.
Keywords- Armoured Vehicle, Binding Agent, Bullet Proof, Composite,Empty Fruit Bunch, Oil Palm, Potato, Prepregs, Starch
In this study, the effect of the wheat straw with different fiber concentration (5 to 25% by weight) on the mechanical properties of the polystyrene composites were studied. The polystyrene composites of wheat straw were prepared by Haake Rheocord 9000 twin screw extruder machine. The standard test specimens were molded on compression moulding machine. Mechanical properties were determined using these test specimens. It was found that with the addition of wheat straw as filler in polystyrene composites, tensile strength, impact strength and hardness are found to increase with increase in wheat straw concentration.
Keywords- Polystyrene, Wheat Straw
Thermoplastics have become essential part of our everyday lives. Our cars and appliances contain more and more plastic every year. In the present work effect of fly ash in different concentrate on such as(5%,10%,15%and20%) with different particle sizes on mechanical, electrical, morphological, rheological properties of POM composites was studied. The mechanical properties such as tensile strength and impact strength is found to be decreasing marginally while flexural strength and elastic modulus is found to be increasing with increase in % loading of fly ash. The dielectric strength of the composite increases with the increase in % loading of fly ash and is found to be higher for smaller particle size. Morphological studies reveals that there is good dispersion of filler in the composite.
Keywords- Fly ash, Polymer composites, Polyoxymethylene (POM)
In stand-alone micro-hydro power system, water turbine will vary in speed due to the variation of consumer load. This speed variation will cause in fluctuation in both voltage and frequency output from a generator. To solve this problem, electronic load controllers were invented and used by using single method in micro-hydro power system. Although using single method may satisfy for low power rating, it can not only generate the large amount of harmonics but also reduce the control resolution of system for large power rating. In this paper, combination method of binary load regulation and pulse width regulation is used to be minimal harmonic effect into the power system and to improve the control resolution. Microcontroller based proposed ELC design is simulated and studied on LCD display by Proteus 8 professional software.
Keywords- Binary Load Regulation, Combination Method, Electronic Load Controller (ELC), Pulse Width Regulation, Stand-Alone Micro-Hydro Power System.
Solar thermal energy produces immediate environmental benefits. Solar thermal energy can be converted into electrical energy with the help of parabolic trough electrification system. Electricity can be produced directly from thermal energy using solar thermal collectors which can generate heat energy for a working fluid. Myanmar is situated in the Northern hemisphere. Therefore, the solar collectors must be placed south-facing position when the solar radiation is calculated. To generate the required electrical energy of 30 kW, the total area of the installed collectors is about 194 m2. The concentrator has an aperture of 1.4 m and a length of 1.4 m, while the absorber tube (0.0315 m inner diameter and 0.0325 m outer diameter). The outlet temperature of working fluid (molten salt) was 763.4994 ̊C in April and 752.9932 ̊C in December. As the rated capacity of a model village is greater than 500 W, the selected nominal system voltage must be DC 120 V. In this paper, design calculation of solar thermal electrification consists of calculation of series and parallel collectors, daily load consumption and distribution system for desired loads for day and night, and estimated cost of electrical components for 400 V distribution system.
Keywords- Parabolic Trough Collectors, Daily Load Consumption, Distribution System, Solar Intensity
Energy is the major input for overall economic development of the society. Among them, wind energy is the fastest growing renewable energy source. This paper proposes a control strategy for a variable speed stand-alone wind power supply system with battery energy storage system. Wind turbine is connected with permanent magnet synchronous generator (PMSG), switch mode rectifier, DC-DC bidirectional converter, battery bank, and voltage source inverter. Control of the switch mode rectifier is used to extract maximum power from available wind power. DC-DC bidirectional converter control is used to store the surplus energy and to discharge this energy when wind power is shortage. A voltage source inverter with Pulse Width Modulation (PWM) control is used to get the stable load side output voltage. The complete control scheme for wind power generating system has been applied using MATLAB/SIMULINK to supply the desire load.
Keywords- Battery bank, DC-DC Bidirectional Converter, Diode Rectifier, Permanent Magnet Synchronous Generator, Voltage Source Inverter
In Myanmar, a lot of power is remarkably dissipated in distribution system. There are two types of losses in power distribution system namely technical and non-technical loss. Accurate loss reduction and voltage stability improvement are the critical components for efficient electrical distribution power flow. There are several ways for line loss reduction and voltage profile improvement. Specifically, network reconfiguration method is employed for the proposed system. The power flow analysis of base case is done by using an advanced software known as ETAP 7.5 version. The inputs are given based on the real time data collected from 33/11kV substations under Yangon Electricity Supply Board (YESB). Network reconfiguration in distribution systems is performed by opening sectionalizing (normally closed) and closing tie (normally open) switches of the network. The most important benefit of network reconfiguration is loss reduction, voltage profile improvement and freeing up the power system capacity. The proposed method is tested on a 74-Bus distribution network. It is situated in Dagon Seikkan Township, Yangon Division. This network is chosen as a case study for this paper since it has a lot of industrial loads that cause reduction of system efficiency. Power distribution of the studied system is overhead AC radial distribution system. The distribution network reconfiguration was modelled by MATLAB tool. Particle swarm optimization method is applied to get the optimal switching scheme for network reconfiguration. Simulation results from load flow analysis have shown that the implementation of this project leads to a significant enhancement in voltage profile, reduction in the real power loss and percentage of real power loss. Finally, study results of system loss reduction and voltage stability enhancement with brief overview of approached model for proposed system are revealed in this paper.
Keywords- Loss Reduction, Network Reconfiguration, Particle Swarm Optimization, Voltage Stability Improvement
Axial-flux permanent magnet (AFPM) machines have become an important subject of study because of the development of neodymium magnets over the past 20 years. Axial-flux machines have high power density and high torque. Axial-flux permanent magnet machines have many unique features. For being permanent magnet, they usually are more efficient, as field excitation losses are eliminated, reducing rotor losses significantly. Machine efficiency is thus greatly improved, and higher power density achieved. Axial-flux construction has less core material, so, high torque-to-weight ratio. The noise and vibration they produce are less than those of conventional machines. Their air gaps are planar and easily adjustable. The aim of this paper is to perform more accurate design calculation and analysis of an axial-flux permanent magnet synchronous generator, double-sided with external rotors and internal slotted stator. The evaluation is based on theoretical analysis by means of sizing equations and confirmed by finite-element analysis. Therefore, the AFPMSG topology considered in this paper is a three-phase double-rotor single-stator topology with 16 pole-pairs, 2kW rated power and 188 rpm rated speed. The performance of double-sided APMSG for slotted stator design is analyzed with finite element analysis (FEA).
Keywords- Axial-Flux Permanent Magnet Synchronous Generator (AFPMSG), Double-Sided, Finite Element Analysis (FEA), Slotted Stator.
The dynamic model of doubly fed induction generator (DFIG) wind turbine including models for both mechanical components as well as for all electrical components. It is also consisting of controllers and protective device for this model during grid faults. The main aim of this paper is to modelling of a variable speed wind turbine with doubly-fed induction generator (DFIG). They are widely used in wind energy generation systems. Here, the rotor is considered fed by a voltage source converter (VSC) whereas the stator is connected to the grid directly. A mathematical model of the machine is written in appropriate d-q reference frame that is established to investigate simulations. The capacity of the wind power generation is 2MW. The voltage rating and frequency for this system are 690V, 50Hz. The location of wind turbine is selected at near the Sitaway Area, Rakhaing State (range from 4 to 8 m/s) which is one of the possible wind power generation sites in Myanmar. This paper describes modelling, simulation, reactive power control strategies and performance analysis of DFIG coupled with wind turbine.
Keywords- Doubly-fed Induction Generator, Modelling and Simulation, Reactive Power Compensation, Variable Speed Wind Turbine, Voltage Source Converter.
The intention of this paper is two folds, one to review selected tree search algorithms / search strategies that can be applied to a problem space and the second objective is to stimulate to implement recent developments in the complexity behavior of search strategies. The algorithms discussed here apply in general to both brute force and heuristic searches over tree spaces.
Keywords- Trees Search, Asymptotic Complexity, Brute Force, Heuristics Algorithms
Cloud computing is a relatively new concept, so it is unsurprising that the security of information and data Protection concerns, network security and privacy still need to be addressed fully. The cloud computing allows clients to avoid hardware and software in Investments, gain flexibility, and cooperation with others, and to take advantage of sophisticated Services. However, security is a big problem for cloud computing clients especially access control; client profiles management and access services provided by public cloud computing environment. This article we are proposing an authentication model for cloud computing based on the Kerberos V5 protocol to provide single sign-on and to prevent against DDOS attacks in the access control system. This model could benefit by filtering against unauthorized access and to reduce the burden, computation and memory usage of cloud computing against authentication checks for each client. It acts as a trust third party between cloud computing servers and clients to allow secure access to cloud computing services. In this paper we will see some of the related work for cloud computing access control security issues and attacks. Then in next section we will discuss the proposed architecture.
Keywords- Cloud, Role Based Access Control, Authentication Protocol, Key Distribution
In this work, a novel method is proposed that utilizes depth information of human body to retrieve appropriate posture from a database. The retrieval method utilizes Enhanced Independent Component Analysis (EICA) of depth postures of different classes over which Linear Discriminant Analysis (LDA) is performed. Then, the postures of each class are ranked in sorted order based on the distance to their class center. To retrieve a testing posture from the training database, the posture is projected on the feature space based on which its class is determined by measuring the distances to all class centers. Finally, a binary search is done in the corresponding class to find the nearest distance of the corresponding posture and the one is chosen with the least distance.
Keywords- EICA, LDA, Depth, Posture.