Bangkok, Thailand 05-06-2017
Using charge-coupled devices and CMOS sensors in spectrometers increases device cost due to complex circuitry requirements. In this work, a single beam visible spectrometer is designed and built using a single photodiode as a sensor and a simple circuitry hence reducing the cost of the device. Moreover, on the market, most of the spectrometers use 16-bit analog to digital converter to convert analog signal thereby limits the measurement concentration resolution and sensitivity of the spectrometers. To extend its ability, a 24-bit ADC is used in the design for more accurate spectrum measurements. This single beam visible spectrometer works in the spectral range from 400nm to 750nm. The use of the trans-impedance amplifier and smoothing sensor reduces noise and increases accuracy of the measured spectrums.
Keywords - Visible light spectrometer, noise, photodiode, filter.
To gain higher analog output levels from digital systems, a high resolution DAC is required, which is usually a cost tradeoff. This research demonstrates an affordable way to increase the DAC resolution with a low cost microcontroller. It works by merging 3 PWM signals which are generated by an ATMEGA328 microcontroller in order to be used as an input into an RC digital to analog voltage converter. The merging is completed by using digital circuit, which produces a new carrier frequency by reducing the original PWM carrier frequency by a half. The new carrier frequency is merged with 2 PWM signals by logical operation. The theories and experiment results reveal that converting the united PWM signal to analog voltages is possible. The conversion outcome is the improvement in analog voltage output resolution when compared to the conversion from a single PWM.
Keywords: ATMEGA328, Microcontroller, Digital to Analog Converter, DAC, PWM, Resolution
The aim of this paper is to design the heliostat field layout of solar thermal generation for a CSP plant, based on the central power tower technology. In this design, the radial staggered pattern is proposed to reduce the shadowing and blocking losses. Its solar field consists of 1150 heliostats around a 95m tall tower and each heliostat has a 121m2 reflecting area. The power plant is designed to produce an output of 56MWth thermal power with molten salt storage system. The coordinates of the chose location for this plant are 19.7633˚ (Latitude) and 96.0785˚ (Longitude), which is a city called Naypyitaw, Myanmar. To evaluate the available solar thermal power received at the central receiver, the optical efficiency which is the product of the mirror reflectivity, the atmospheric attenuation efficiency, the shadowing and blocking efficiency and the cosine efficiency is proposed as well. Results show that the annual optical efficiency increases and the minimum value of thermal power received on the tower receiver is greater than required power.
Keywords- 56 MWth, Atmospheric attenuation efficiency, Central power tower technology, Cosine efficiency, Heliostat field layout, Molten salt storage system, Optical efficiency, Shadowing and blocking, Solar thermal power.
Nowadays, renewable energy sources, wind power is one of the most attractive solutions. AC/DC/AC power converter extracts power from variable speed permanent magnet synchronous generator (PMSG) and feed it to supply a standalone load. The output voltage and frequency of the PMSG is variable in nature due to non uniform wind velocity. Therefore, power electronic converters are needed to get constant frequency and constant voltage. The variable three-phase AC output at the PMSG is rectified by a diode rectifier and the DC link is maintained constant by a thyristor crowbar. Thyristor crowbar is provided with silicon controlled rectifier (SCR), transistor and zener diode. The crowbar circuit is used to protect the battery from over voltage of rectifier output voltage. The converter output is fed to three-phase inverter which employs a SPWM technique, the output of which can be fed to a load or grid. The inverter circuit oscillates DC voltage or current into a desired AC voltage or current waveform and frequency. Circuit simulation and analysis was done by Proteus (8.3 Professional) and MPLAB IDE. The wave shaping timing pulses are generated by using microcontroller PIC16F628A and required signals are generated for the driver circuit of the inverter.
Keywords- Converter, Permanent Magnet Synchronous Generator (PMSG), Standalone Load, Thyristor Crowbar, Wind Power.
Inadequate attention during design and construction of some of reinforced concrete (RC) buildings has raised questions about the performance level of these existing buildings under future earthquakes. This paper aims to evaluate seismic improvements of existing RC buildings. For this, total of five existing RC buildings constructed in major seismicity zone, Mandalay city, are selected. Two possible improvement solutions are proposed; steel bracings and RC shear walls. Linear static analysis is carried out for structural stability checking of existing structures based on UBC 97 code. From these checkings, deficiencies of P-∆ effect are found in three existing pinned based buildings and deficiencies of torsional irregularity are also found in two existing buildings. Firstly, structural improvements under linear static analysis are performed to correct these deficiencies. Then, nonlinear static (pushover) analysis is carried out for performance evaluation of existing structures. Seismic performance enhancement of the proposed existing buildings is evaluated to achieve basis safety objective performance level described in FEMA 356. Results show that RC shear wall is more appropriate not as economic solution for more deficient buildings (Model 5) whereas steel bracing is effective solution for less deficient buildings (Model 1, 2, 3 and 4).
Index Terms- Existing RC Buildings, RC Shear Walls, Steel Bracings, Seismic Improvements.
Wind is air movement relative to the earth, driven by several different forces, especially pressure differences in the atmosphere. Therefore, the effects of different wind flow distribution to the cluster structures in an aspect of structural safety should be investigated. In modern cities, there are increasing numbers of high constructions and complex forms which can involve problems of significant wind discomfort around these buildings. In recent years, the numerical investigation has emerged as powerful and sufficient tool for building optimization and a better township planning. Present work proposes the methodology to carry out exterior numerical on a cluster of existing structures. Present work used a three dimensional scale down model of buildings where steady flow analysis has been done. It has been implemented through ANSYS Fluent 17.0 using SIMPLE algorithm as solver. The turbulence models used as the RANS based model: the standard k-epsilon model, RNG k-epsilon model and Realizable k- ɛ model. In this paper, the simulation results have predicted the ring vortex, roof separation bubble, side separation and wake recirculation, but the shapes and locations are different from each other. Wind pressure coefficients compared the three different turbulence models in Fluent. The maximum wind pressure coefficients was found to be at the middle of windward surface with height of about 0.7H-0.8H and the minimum wind pressure coefficient generates at the corner of the flow separation.
Keywords- Computational Fluid Dynamics (CFD), RANS Equation, Cluster of Existing Structures, Wind Pressure Coefficients.
Gear is the most essential element of power transmission. One of the main gear tooth failure is pitting which is surface fatigue failure due to many repletion of high contact stresses occurring in the gear tooth. The work of this paper is to reduce the contact stress happing often on gear by changing the different values of face width. Contact failure in gears can be predicted by calculating the contact stress with AGMA (American Gear Manufacturing Association) equation and also analyzing with ANSYS. The model of helical gear pairs are generated by using SolidWorks software and ANSYS is used for numerical analysis. Ultimately, the results obtained from ANSYS are presented and compared with theoretical values. In this analysis, the face width 21mm which has 493.27 MPa von-Mises stress is selected because of the weight reduction.
Keywords- AGMA, ANSYS, contact stress, face width, helical gear
Leaf springs are widely used as automotive suspension to absorb shock loads. Suspension system in an automobile determines the riding comfort of passengers and the amount of damage to the vehicle. The main function of leaf spring assembly as suspension element is not only to support vertical load, but also to isolate road-induced vibrations. This paper is the work performed towards the optimization of the leaf spring for solar vehicle with constraints of maximum bending stress, von-Mises stress, deflection and natural frequency of leaf spring under safety load condition. Chromium steel AISI 5150 is used for front and rear leaf spring material. In this paper, front and rear leaf spring are analysed by changing various thickness. The thickness and width of the front leaf springs for optimum design are 8 mm and 50 mm. Thickness and width of the rear leaf spring design are 5 mm and 45 mm. The von-Mises stress of front leaf spring is 755.44 MN/m2 and rear leaf spring is 662.50 MN/m2. Working frequency of front and rear leaf spring are 1.466 Hz and 1.815 Hz respectively. Working frequency do not match with natural frequencies of the front and rear leaf spring at six mode shapes. Therefore, the designed leaf spring is safe for modal analysis. SolidWorks software is used for modelling of leaf spring designs and ANSYS software is used for structural and modal analysis of leaf springs.
Keywords- Automobile, Bending stress, Deflection, Leaf spring, Modal analysis, Structural analysis.
A reverse running centrifugal pump is one of the attractive choices in micro-hydropower development and industrial pressure energy recovery. Pumps as turbines have been successfully applied in a wide range of small hydro sites in the world. Since the overall efficiency of these machines is lower than the conventional turbines, their application in larger hydro sites is not economical. Therefore, the efficiency improvement of reverse pumps is essential. In this study, by focusing on a pump impeller, the shape of blades was redesigned to reach a higher efficiency in turbine mode by modification in impeller tip. Modification was done by rounding the blade on impeller tip. After each modification, a new impeller was manufactured and tested in the test rig. The objective of this paper is to improve the efficiency of PAT by modification on impeller tip. In this paper, 3-D numerical CFD tool for simulation of the flow field characteristics inside the pump as turbine are analyzed and simulated by using Flow Simulation in ANSYS Workbench 17.0. According to the experimental and numerical result, the efficiency of impeller round tip is greater than flat tip.
Keywords- Modification, Impeller Tip, Efficiency, Blade Rounding.
Radiations vulcanization of natural rubber latex (RVNRL) has been developed extensively through various research and development programme. This holds important benefits for rubber industries in Southeast Asia and the Pacific Region. Myanmar also develops more and more rubber plantation and many rubber raw materials are processed to manufacture medical products, household items and industrial mechanisms. In this paper, advanced and effective radiation vulcanization technique is utilized to introduce the technology in rubber industries in Myanmar. It uses gamma radiation to initiate vulcanization, a process that chemically bonds molecules to promote rubber elasticity and strength. In the present study, the radiation effect on the vulcanization of natural rubber latex and the synergistic effect of urea addition along with n-butyl acrylate (n-BA) sensitiser on the crosslinking density and physical properties of RVNRL film have been investigated. Acrylate monomer was used in order to reduce the radiation dose required to vulcanize natural rubber latex, originally 300 kGy to 15 kGy. However, there is still a need to further reduce the dose requirement without increasing n-BA concentration. The way to fulfil the requirement is the using of urea. Therefore the various concentration of urea (0.1, 0.2, 0.3, 0.4 and 0.5) (phr) was used. Tensile strength, elongation at break, modulus at 500%, swelling ratio, gel content and crosslinking density were determined. Tensile strength and modulus at 500%, gel content and crosslinking density were found increasing with absorbed dose, as well as the proportion of monomer concentration in the rubber phase in presence of urea. The radiation dose for better cross-linking of natural rubber latex with six parts per hundred rubber (phr) n-BA was 15 kGy absorbed dose from the results. The results show that by addition of 0.3 parts per hundred rubber (phr) urea to the latex before irradiation, the crosslinking density and tensile strength increases respectively.
Keywords- Natural rubber latex, N-butyl acrylate, Urea, Gamma radiation, Vulcanization, Tensile strength, Crosslinking density
Entrepreneurship has been identified as the engine of long-term economic growth of a nation as it is a leading factor in achieving economic growth, high employment, strong job creation, and positive social development. It drives and shapes innovation, speeding up structural changes in the economy. Small and Medium Enterprises are the breeding ground for entrepreneurs to set up their ventures for many reasons. However, the recent statistics depict that the failure rate of SMEs are very high. As a result, a less number of successful entrepreneurs can be seen. Therefore, it is a timely need to promote entrepreneurship among individuals. Thus, entrepreneurial intention of individuals is of critical importance in this regard.The main objective of this study is to find out the factors that affect entrepreneurial intention among the final year undergraduates of the University of Sri Jayewardenepura, Sri Lanka. The study involves three factors, that come under the Theory of Planned Behaviour i.e. attitudes, subjective norms and perceived behavioural control, which affect the entrepreneurial intention of individuals.Also, the study attempts to assess the effect of gender on the said factors. A total of 344 students from four faculties of the University of Sri Jayewardenepura participated in this study by responding to the structured questionnaire. Structural Equation Modelling was used to analyse the data using Smart PLS. Findings of the study revealed that attitudes and perceived behavioural control is positively related with entrepreneurial intention while subjective norms are negatively related with the same. The study also revealed that, only the relationship between subjective norms and entrepreneurial intention is moderated by gender. Further, it was found that, males are more responsive to the subjective norms than the female counterparts.
Keywords - Entrepreneurial Intention, Theory of Planned Behaviour, Partial Least Squares Structural Equation Model, Under graduates.
Indexterms - About four key words or phrases in alphabetical order, separated by commas.
The export sector of a country plays an important role in promoting economic growth and development. Each and every country uses Small and Medium Enterprises (SMEs) as a strategic tool to develop their export sector. The barriers existing in the export market hamper the maximum contribution of SMEsto the development of export sector. This thesis involved an investigation on the export barriers faced by SMEs in the Sri Lankan export market with special reference to manufacturing sector. The main purpose of this study is to identify major export barriers faced by SME exporters in the Sri Lankan export market and major export barriers that hinder SME non-exporters to enter into the Sri Lankan export market. Further, this study aims to identify whether there are differences in the barriers faced by SME exporters and non-exporters of manufacturing sector in the export market of Sri Lanka. In order to achieve the objectives of the study, both qualitative and quantitative approach were used. Self-administered structured questionnaires and in-depth personal interviews were used to collect primary data from the sample by using convenient sampling method. SME owners and managers of manufacturing sector were considered as the respondents. The data obtained from the firm level survey was analyzed using Statistical Package for Social Sciences Version 21.0 (SPSS 21.0). In line with the literature, this study found that the top ten export barriers faced by SME exporters in the export market were high cost of capital to finance exports, lack of government incentives, lack of new technology, complexity of export documentation procedure, lack of financing sources, high tariff and non tariff barriers, currency fluctuations, lack of competitive prices to foreign customers, high insurance cost and inadequate institutional support. On the other hand, the top ten export barriers that hinder SME non-exporters to enter into the export market were complexity of export documentation procedure, lack of government incentives, high cost of capital to finance exports, lack of financing sources, inadequate institutional support,lack of competitive prices to foreign customers, political instability of foreign countries, difficulty in making customer contacts, insufficient information about overseas markets and difficulty in making export quality products. Moreover, the study could reveal that there are no significant differences between the export barriers faced by SME exporters and non-exporters of the manufacturing sector in Sri Lanka.
Keywords - Small and Medium Enterprises, Exports, Export barriers
This study is an attempt to identify the impact of human capital characteristics on access to debt finance. Small and medium sized enterprises of a company plays a major role in the economy of a country. Therefore the development of each SME is vital for the development of a country. When the factors relating enterprise success is concerned, access to debt finance can be identified as a significant factor. Literature suggest many factors which affect the access to debt finance of SMEs. Out of which, this study measures the impact of human capital characteristics on the access to finance. Human capital characteristics such as education, knowledge and expertise have been selected for the study.
Index Terms-Debt Finance, SME, Human capital characteristics
Biodiesel is a renewable transportation fuel consisting of fatty acid methyl esters (FAME), generally produced by trans-esterification of vegetable oils or animal fats. At present, a continuous flow system has been developed to increase manufacturing capacity of biodiesel from waste cooking oil that is generated from a number of sectors. Since waste cooking palm oil contained large amount of fatty acids, which inhibit the trans-esterification reaction and forms soap, it has to be treated in an esterification process first so that the free fatty acids content is lower than 1 wt. % of oil. This research aims to produce biodiesel from waste cooking palm oil in a continuous flow system assisted by microwave irradiation. Esterification of waste cooking palm oil at 60oC, alcohol-to-oil molar ratio of 12:1, catalyst concentration of 6 wt. % of fatty acid, volumetric flow rate of 520 ml/min, was able to reduce the amount of free fatty acids from 2.25 wt. % to 0.56 wt. % of oil. The optimum conditions for the production of biodiesel from treated waste cooking palm oil was at 60๐C, alcohol-to-oil ratio of 12:1 volumetric flow rate of 520 ml/min and the catalyst concentration of 2.5 wt. % of oil, with 99.1% yield and 97.79 wt. % methyl ester.
Index term- Biodiesel, Palm Oil, Transesterification, Esterification, Microwave irradiation.