← All proceedings

THE IIER INTERNATIONAL CONFERENCE

Proceedings cover: THE IIER INTERNATIONAL CONFERENCE

Kiev, Ukraine 17-07-2018

4 papers

  1. Dependency of The Dendritic Microstructures on The Growth Rate in The Directionally Solidified 7020 Alloy

    Hasan Kaya, Emin Cadirli, Mevlut Sahin, Ugur Buyuk

    Paper ID II-APMKIEV-17078-10516 · Pages 1

    Abstract

    7020 aluminum is a 7000-series aluminum alloy: the main alloying addition is zinc and it is formulated for primary forming into wrought products. 7020 is the Aluminum Association (AA) designation for this material. In European standards, it will typically be given as EN AW-7020. H17 is British Standard designation. The aim of this work is to investigate the relationship between growth rate, V, and dendritic microstructures (primary dendrite arm spacing, 1, secondary dendrite arm spacing, 2, dendrite tip radius, R and mushy zone depth, d), in the EN AW-7020 alloy (Al- 4.5 wt %Zn- 1.2wt %Mg-0.15 wt %Cr-0.15 wt %Zr) alloy. In order to achieve this aim, the specimens were solidified under argon atmosphere and steady-state conditions upward with different growth rate, V for EN AW-7020 alloy in the Bridgman type directional solidification apparatus. The dendritic microstructures were measured and expressed as functions of growth rate by using linear regression analysis. Theoretical models for the dendrite arm spacings and tip radius have been compared with the experimental observations, and a comparison of our results with the current theoretical models and previous experimental results have also been made.
    This research was supported by the Erciyes University Scientific Research Project Unit (FBA-2017-7241)

    Index Terms- 7XXX alloys, directionally solidification, microstructure.

    Download PDF
  2. Mechanical Properties of 7020 Alloy Produced By Directional Solidification

    Ugur Buyuk, Emin Cadirli, Mevlut Sahin, Hasan Kaya

    Paper ID II-APMKIEV-17078-10656 · Pages 2

    Abstract

    The 7020 alloy belongs to the hardenable Al–Zn–Mg-based alloys, which are the group of the high strength aluminium alloys and are used for some structural applications in the aircraft (components in wings and ailerons) and automotive industry (bumper structures). In this study, the effect of solidification rate (V) on the mechanical properties (microhardness and ultimate tensile strength) of 7020 alloy (Al-%4.5Zn-%1.2Mg-%0.15Cr-0.15%Zr wt.%) has been investigated. The 7020 alloy was prepared using metals of 99.99% high purity in the vacuum atmosphere. At a constant temperature (8.3 K/mm), these alloys were directionally solidified upwards under various V (8.3–166 m/s) using a Bridgman-type furnace. Microhardness and ultimate tensile strength at room temperature were examined. The microhardness increased from 75.88 to 91.71 MPa and the ultimate tensile strength increased from 125.43 to 208.11 MPa with increasing the solidification rate from 8.3 to 166m/s. Exponent values of the V for the microhardness and ultimate tensile strength were calculated as 0.07 and 0.18, respectively.
    This research was supported by the Erciyes University Scientific Research Project Unit (FBA-2017-7241)

    Index Terms- 7XXX alloys, directionally solidification, microhardness, tensile strength.

    Download PDF
  3. Fault Tolerance Improvement of The Secured Circuits

    Ghania Ait Abdelmalek, Rezki Ziani, Rabah Mokdad

    Paper ID II-RIETKIEV-17078-11447 · Pages 52-54

    Abstract

    One of the major problems in testing a system-on-chip is dealing with the optimal choice of the test sequence. In this paper, we propose an efficient test sequence for TMR secure circuits. The test sequence is a high level method based on three pulsations. An extension to the sequence with one pulsation is proposed and by simulation results its effectiveness in achieving a higher fault tolerance interval is demonstrated.

    Download PDF
  4. The Effect of Combined Drug Treatment on Hl60 Leukemia Cell Survival : Drug Repurposing

    Belgin s. Isgor, Yasemin g. Isgor, Nazli balkan

    Paper ID II-NSEKIEV-17078-12266 · Pages 55-58

    Abstract

    Drug discovery and development efforts generally do not provide a new drug into the market but deliver the scientific information to be used in the development of diagnostics and therapeutics. Generally drugs highly metabolized by detoxification system enzymes, such as Glutathione Transferases (GST), are of the limited use in clinics. In that sense the aim of the work is to evaluate the novel effect of Doxazosin, the drug with antihypertensive effect, in combination with anticancer drugs on HL60 cells. The study was also designed to evaluate the effect of combined drug use against the GST target. The results revealed that the treatment of cells with 5 nM SU6656 resulting in GST activation was reversed in the presence of Doxazosin with almost 50% inhibition of that enzyme. On the other hand Genistein alone resulting 57% GST inhibition was not significantly lowered in the presence of Doxazosin. Therefore it may be suggested that use of doxazosin with isoflavonoid or indolinone derivative drugs may enhance drug effectiveness.

    Keywords- doxazosin, SU6656, Genistein, Glutathione Transferase, Cytotoxicity, combined therapy, drug discovery.

    Download PDF