Kuala Lumpur, Malaysia, 12-02-2015
ISBN 978-93-84209-87-2
In this paper we will investigate whether or not the writhe of knot is an isotopy invariant? By adding a parallel strand to an oriented knot/link, we will justify that writhe is a useful isotopy invariant. Since helicity has its origin in knot theory, consequently, we will eatablish that helicity is an isotopy invariant which will be useful to study plasma physics, solar physics and astrophysics.
Keywords- Writh, Isotopy Invariant, Magnetic Field, Reidemeister Moves, Helicity.
The Cantabro durability test is usually used for open graded asphalt mixtures and has seen little use with dense graded mixtures. This paper presents durability data from the Cantabro test for Palm oil fuel ash (POFA) modified dense graded asphaltic concrete AC 14. The nature and amount of filler in an asphaltic concrete mixes significantly affect its design and performance. POFA is an ash obtained from the burning of waste material generated from the production of crude palm oil which is of high quantity in Malaysia. A number of trial mixes were prepared using the Marshall Mix design procedure with 5% POFA and 1% Ordinary Portland Cement (OPC) as filler materials to arrive at asphalt concrete mixtures that fulfil the Marshall criteria. Cantabro durability test was used to measure the durability of the asphaltic concrete. The results show that Marshall stability, flow, stiffness and cantabro loss values shows general improvement for the POFA modified asphalt compared to the control specimens.
Keywords- Palm oil fuel ash (POFA), Filler, Durability, Asphaltic Concrete.
In the paper the simplified criterion of a steady-state stability of electric power systems (EPS) is justified on the basis of Lyapunov functions in a quadratic form ensuring necessary and sufficient conditions of its performance. Upon that, use of the node-voltage equations allows reducing study of a steady-state stability of complex EPS to study of the generator-bus system. The obtained results facilitate studies of a steady-state stability of the complex systems and have the practical importance.
Keywords- Simplified Algorithm, Stability, Electric Power System, General Theory, etc.
This study proposes Meta model approaches as a new intelligent technique for the explicit formulation of friction factors of water conveyance structures. For this purpose, experimental Data of movable bed Flume with dune bed form was used. Analyzing the result clears the high capability of Meta model approaches (MNE= 0.05, R= 0.92) as a powerful tool for optimizing and explicit simulation of Manning roughness coefficients of water conveyance structures compared other nonlinear approaches.
Keywords- Intelligent Techniques, Explicit Simulation, Roughness Coefficient, Experiments
Organizations pursue policies and strategies to gain competitive advantage against their competitors. To overcome cost issues and production quality issues, many organizations adopt lean manufacturing techniques such as 5S and TPM. However, many of these organizations especially in developing countries face problems in effective and successful implementation of these techniques 5S and TPM. This is mainly due to lack of employee related factors that are not considered when organizations adopt these techniques. The present study attempts to investigate the role of ethical factors in the implementation of 5S and TPM. The results of the study reveal that manager-subordinate relationship (empowerment) is having insignificant influence on the implementation of 5S and TPM; while ethical training and ethical instructions and commands are found to be influential in the implementation of these techniques. The study provides limitations and future directions for researchers interested in the area.
Keywords- 5S, TPM, Manager-Subordinate Relationship, Ethical Training, Ethical Instructions And Commands, Developing Country, Iraq.
This study examines a new concrete barrier design that is applied in regions where vehicles are disallowed entry. A new model shape that is composed of three parts is constructed in the proposed design. Finite element analysis is conducted with ANSYS computer software to verify the failure effect of parts during impacted load with different velocities. Results show that the new model can efficiently consider the impact load in one part when the total load effect is examined. The other parts remain with no crack or damage. The stresses and strains in the concrete part affected by the applied load gradually change with the increase in load velocity. The findings also indicate that the concrete barrier system protects road users in case of vehicular accidents.
Keywords- Concrete barrier, ANSYS software, Finite element, Failure.
In this study, we have a demonstrated a new technique to enhance the photosensitivity of germanosilicate fiber based on KrF excimer laser irradiation prior to grating inscription process. Fibers treated with 248nm KrF excimer laser provides a two times higher refractive index change compared to the untreated optical fiber. The increment of the 193nm UV absorption band with KrF excimer laser irradiation which is associated with the germanium related oxygen deficient centers, is believed to be the reason for the enhancement of the photosensitivity with 193nm ArF excimer laser irradiated fiber Bragg gratings.
Keywords- Bragg Gratings, Photosensitivity, 248nm KrF Excimer Laser, 193nm ArF Excimer Laser
Biosurfactant or microbial surfactants produced by microbes are structurally diverse and contribute in reducing surface and interfacial tension. Apart from being isolated of municipal waste and oil contaminated soil, biosurfactant-producing Bacillus subtilis can also be found in fermented foods as well. In this study, we isolate potential biosurfact-producing Bacillus subtilis from Malaysian traditional fermented foods and do qualitative screening (drop collapse, oil spreading and hemolysis assay) for biosurfactant producer activity.
In this study, surface modification of oil palm empty fruit bunch fiber (OPEFB) was carried out through treatment with ultrasound in 2% sodium hydroxide solution. Surface morphology of the fiber was studied by scanning electron microscope (SEM) analysis, and structural changes to the fiber with respect to treatment were investigated through Fourier transforms infrared spectroscopy (FTIR) analysis and X-ray diffraction (XRD) analysis. Furthermore, thermal stability of the treated fiber was investigated through thermogravimetric (TGA) analysis. Morphological changes in form of opened pore spaces and structural changes through disappearance, reduction and shifting of functional group intensities were observed for the fiber after ultrasound treatment as revealed by SEM and FTIR analysis. Density measurement revealed increased density of OPEFB fiber with respect to ultrasound treatment and also increased crystallinity was confirmed by XRD studies. Moreover, thermal stability of the fiber was found to increase after ultrasound treatment.
Keywords- Ultrasound, Surface Morphology, Structural Analysis, Oil Palm Empty Fruit Bunch Fiber.