← All proceedings

271ST THE IIER INTERNATIONAL CONFERENCE

Proceedings cover: 271ST THE IIER INTERNATIONAL CONFERENCE

Jakarta, Indonesia 12.12.2019

6 papers

  1. Finite Element Analysis of Rack-Pinion System of a Jack-up Rig

    Khondaker Sakil Ahmed, Md Wahidul Islam, Ibriju Ibrahim

    Paper ID IA-ICCAEKBALI-13129-13533 · Pages 1-5

    Abstract

    In offshore mobile jack-up rig, platforms are generally supported by movable jacking system where strength of rack and pinion are very crucial in determining the design life of the superstructure. In this study, a number of finite element models have been developed for noble 7 teeth-pinions to investigate the strength of this jacking system. Since rack-pinion contact patterns change with the rotation of the shaft, models are developed for every 10 degree rotation starting from 0 to 50 degree where elasto-plastic properties of both rack and pinion is considered. Therefore, it is expected that each pinion tooth experiences different stress and displacement as it contacts with rack at different orientation. Elasto-plastic finite element analyses are conducted for worst possible load cases of the gear including self-weight of the platform, wind load, hydrodynamics force as per American Bureau of Shipping (ABS) guideline. The stress distribution of the pinion shows that maximum stress occurs at the root of the tooth, mainly due to bending effect. The analysis reveals that maximum stress in rack and pinion are found to be 1103 MPa and 682 MPa, respectively which is very close to the corresponding material capacity. The outcome of this study will certainly contribute in designing future rack-pinion system for offshore jack-up rigs and similar other structures.

    Keywords - Rack-pinion, Finite element, Geometric Analysis, Stress Analysis.

    Download PDF
  2. Analysis of Von Mises Stress of Sweeper Component in Electric Sweeper Car Prototype

    Puji Prasetyo, Elvan Arydoni Budi Susilo, Wikan Sakarinto, Isworo Djati

    Paper ID II-RIETJKRT-12129-17280 · Pages 6-10

    Abstract

    Indonesia is in the second place of the world’s countries that produces the most plastic waste after China. As a solution, large cities in Indonesia such as Jakarta, Bandung, and Yogyakarta have started to take special care of their waste management by taking advantage of sweeper cars. The purpose of this special care is to increase effectiveness and rate at which waste removal is performed. High price has been one of the factors that hinders the possession of sweeper cars by other cities, considering the need to import one. Therefore, a research that aims to produce a design of more affordable and eco-friendlier sweeper car needs to be carried out, given that a sweeper car generally uses fossil fuel which produces air pollution as a result of its exhaust gas. A prototype of electric sweeper car is a new technology of sweeper car that is eco-friendly since it is powered mainly by electricity so that it does not produce exhaust gas. This research aims to produce a design of sweeper component with safe and efficient mechanical system. The design process was done on SolidWorks 2017 software and proceeded by Finite Element Analysis which seeks to analyze the characteristics of static load on sweeper component and to determine its von Misses stress and safety factor. The design of the component produced a result which shows that material used for the sweeper is AISI 1045 mild steel with yield stress of 530 MPa and housing motor’s safety factor of 23.5, letter C’s safety factor of 29,12, triangle plate’s safety factor of 10,33, and letter U’s safety factor of 8,52, and arm top/bottom’s safety factor of 76,92. Overall safety factor of the component is more than one, which is then considered safe.

    Keywords - Sweeper, Safety Factor, Von Mises Stress, Electric Sweeper Car.

    Download PDF
  3. Hydraulic System Design for Electric Sweeper Car Prototype

    Bayu Setiawan, Naufal Adiharto, Wikan Sakarinto, Isworo Djati

    Paper ID II-RIETJKRT-12129-17282 · Pages 11-15

    Abstract

    Waste problem in Indonesia, especially in the urban areas, has been left unresolved. This phenomenon is caused by the significant increase in the development of urban areas in Indonesia, that contributes to the rise in the remnants of the development in the form of waste. One of the measures taken by the governments to deal with the problem, in addition to using human power to clean up the litter in the streets, is by using sweeper cars. However, the sweeper cars’ high price as a result of the import fees has been regarded as an obstacle. Taking this recent condition into account, a research that intends to invent a new technology for more affordable and eco-friendlier sweeper cars needs to be performed, considering sweeper cars in Indonesian market are still using fossil fuel. A prototype of electric sweeper car is a new breakthrough in sweeper car technology as it is mainly powered by electricity. This research aims to design a hydraulic system for the electric sweeper car prototype using SolidWorks software and also to design a hydraulic component layout and a hydraulic circuit (using FluidSIM software), and to calculate the specifications of the cylinder, hydraulic pump, and electric motor. The design yielded a result in the form of specification data of hydraulic system, which consists of several parts: external gear pump with displacement of 1,16 cc/rev and power of 110 watt, electric motor with power of 550 watt and speed of 1200 rpm, cylinder sweeper & arm with inside diameter of 12 mm, rod of 8 mm, stroke of 200 mm, cylinder vessel with inside diameter of 40 mm, rod of 22 mm, stroke of 500 mm. Moreover, cylinder vessel door has inside diameter of 16 mm, rod of 10 mm, stroke of 500 mm, tank with 16 liters capacity, 4/3-way control valve, and solenoid. In addition, sweeper control system uses lever and dump vessel uses button.

    Keywords - Hydraulic System, Electric Sweeper Car, Sweeper Car

    Download PDF
  4. Chassis Design for Electric Sweeper Car Prototype Unit

    Nanda Dewi Arianti, Raka Hafizd Utama, Wikan Sakarinto, Isworo Djati

    Paper ID SF-RASET-YGRT-12129-243 · Pages 16-21

    Abstract

    Organic and inorganic residual waste and litter have become one of the never-ending problems in rural and urban areas and therefore a special care is required to deal with this particular problem. Sweeper cars have been part of this special care in addition to efforts utilizing human power. However, this attempt has its limitation considering their high price after factoring in the import cost. Taking this condition into account, a research on sweeper car that incorporates latest technology and is affordable, yet eco-friendly needs to be conducted. It is because sweepers cars in the market generally use fossil fuel which is not eco-friendly. An electric sweeper car prototype is a newest breakthrough in technology because this sweeper car is electrically powered. This research aims to design a chassis of an electric sweeper car prototype that is safe to be used as a supporting frame of the weight that will be borne by the electric sweeper car prototype. The process of designing chassis was started from observing the design of the unit to get the exact and proportional dimensions to fixing the sweeper car components to the chassis. The entire process was done on SolidWorks 2017 software and later in order to determine the static weight of the chassis and safety factor value, a von Misses stress analysis test was carried out. Creating the design of the chassis yielded a result which contained information about material data of the chassis—it uses AISI 1045 mild steel which consists of 0.43% – 0.50% carbon. This material is chosen because this type of material is easy to be molded and also it has good engine capability and high ultimate and yield strength with maximum yield stress of 530 MPa. von Mises stress analysis test result showed that it has maximum stress value of 86.2 MPa and safety factor value of 6.14. Based on the data above, this design of chassis is considered safe and to meet the criteria for an electric sweeper car prototype.

    Keywords - Design, Chassis, Stress Analysis, Safety Factor

    Download PDF
  5. Analysis of Factors Affecting Implementation Strategy and their Effect on Success and Company Performance

    Friska Sipayung, Liasta Ginting

    Paper ID II-SSEJKRT-12129-17111 · Pages 22

    Abstract

    The most recent comprehensive model of strategic management emphasizes the relationship between performance measurement and strategy implementation and strategy control as a dynamic unitary model. The literature study on various supporting factors for the strategy produces a number of complex factors that determine the success of strategy implementation. Previous research shows very different supporting factors and some of them cannot be applied in all types of organizations.This study aims to identify the capability factors supporting the success of cross-company strategy implementation, analyze the influence of quality implementation stages and implementation support capabilities on successful strategy implementation, and analyze the effect of implementation success on company performance. The research approach used is the Research and Development approach, with a combination of qualitative and quantitative research. The research was conducted at companies in various industrial fields in the city of Medan.The sampling technique used convenience sampling.The research data was processed using the Structural Equation Modeling (SEM) technique of SmartPLS application. The results of the research show that the quality of the stages of strategy implementation have an effect on the success of the implementation. The capability supporting of the strategy have an effect on the success of the implementation. The quality of the stages of the strategy implementation influences the performance of the company.

    Keywords - Strategy Implementation, Supporting Capabilities, Corporate Performance.

    Download PDF
  6. Generalized Level of Service (LOS) for Weaving Section of Conventional Roundabout

    Jezan Md Diah, Raha Abd Rahman, Suria Haron

    Paper ID WF-ISET-BALI-14129-125 · Pages 52-58

    Abstract

    This paper presents a development of weaving section flow model in weaving area of conventional roundabout. The outcomes were very satisfactory, indicating that the parameters considered were very crucial and relevant. Integration of weaving section capacities (QWSF and QP) enable LOS chart be developed that suit Malaysia conventional roundabout (design and operational). This being specified because of the constraint/limitation of using Arahan Teknik (Jalan) model and operational characteristics of the developed model (TISG). The main limitation of Arahan Teknik (Jalan) model in estimation capacity analysis is because it applies geometric design parameters without considering the traffic parameters such as flow and gap, and this may be considered an optimistic or ideal scenario. However, before a roundabout to be constructed, its maximum flow needs to be anticipated in order to reduce the probable traffic congestion. It can be anticipated that the Arahan Teknik (Jalan) model only can determined its capacity of weaving section based on its length of weaving section L, width of weaving section W and average entry width e. The resolution of congestion problem at weaving section is to get better estimation of flow and anticipated LOS at weaving section area under different range of traffic condition regimes such as ‘weaving section flow’ and ‘ideal safe gap’. It will produce different sensitivity of the input parameter of the calibrated models in estimating the respond parameter QWSF which is used as the measures of effectiveness in weaving area of conventional roundabout. With adequate knowledge anticipated flow and using the developed LOS the appropriate design parameters are deduced to suit the target LOS. Thus, this section has developed a ‘tool’ for practicing traffic engineer and the procedure of using it had been deliberated through stepwise example.

    Keywords - Weaving Section Flow; Weaving Section Capacity; Conventional Roundabout

    Download PDF