← All proceedings

25th TheIIER INTERNATIONAL CONFERENCE

Proceedings cover: 25th TheIIER INTERNATIONAL CONFERENCE

Kuala Lumpur, Malaysia, 02-05-2015

ISBN 978-93-85465-05-5

13 papers

  1. The Effect Of The Recycled Aggregate On The Mechanical Properties Of Concrete

    Abobakr Elsadig Gismallah Elwakeel

    Paper ID II-ICEMEIMAL-02055-1349 · Pages 1-5

    Abstract

    This paper investigates the mechanical behavior of concrete prepared with recycled aggregates and fly ash. The results showed that the reduction in the strength was in direct proportion with the amount of fly ash added; the average reductions in the compressive strength was 21% for the 33% fly ash replacement and 61% for the 66% fly ash replacement. And the average reductions in the flexural strength were 15% for the 33% replacement and 41% for the 66% replacement. This indicates that fly ash replacements higher than 33% are not recommended in concrete prepared with recycled aggregates in members that are structurally critical.

    Keywords: Aluminium Fly ash, recycled concrete aggregate, mechanical properties

    Download PDF
  2. Whole-Cell Based Fluorescence Biosensors For Environmental Applications

    W. N. Aisyah, Chai Mee Kin, Wong Ling Shing

    Paper ID II-ICEMEIMAL-02055-1455 · Pages 6-11

    Abstract

    Download PDF
  3. Reed-Solomon And Convolutional Codes On Modulation Schemes For Power Line Communication (PLC)

    Peter O. Aiyelabowo, A. Sali, Samsul Bahari B. Noor, Bamidele Adebisi, Nor Kamariah Noordin

    Paper ID II-ICRACEIMAL-02055-1379 · Pages 12-22

    Abstract

    Download PDF
  4. Prevalence And Risk Factors Of Musculoskeletal Disorders Among Workers Of The Assemble Parts Of The Factory Battery

    M Motamedi, Hr Mokhtarinia

    Paper ID II-ICSTEMIMAL-03055-1512 · Pages 23-27

    Abstract

    Introduction: Musculoskeletal disorders are the most common occupational injuries and constitute a huge global health problem with substantial economic and human cost as well as negative impact on the quality of life. The aim of this study was to determine the prevalence of musculoskeletal disorders among the workers of the montage part of a factory.
    Materials and methods: In this descriptive cross-sectional study performed in 2013, 138 workers aged between 20 and 46 years from the montage part of a battery construction company filled out the NORDIC questionnaire. Also, for the assessing physical posture during work RULA method were applied and filled out by researcher.
    Results: Our results show that the majority of the recruited population suffer from upper back (%30.4) and neck pain (%26.1) and lower back pain(%18.1) then by knee pain (%11.6) respectively. Also results of RULA method analyzing showed that risk level score for 31.2, 53.1 and 15.6% of all postures were 4, 3 and 2 respectively.
    Conclusions: The prevalence of MSDs in the worker was high. Most of postures are needed to be corrected because of high score in RULA method.

    Keywords: Musculoskeletal Disorders؛ Prevalence؛ Battery industry؛ NORDICK questionnaire؛ RULA

    Download PDF
  5. Thermal Diffusivity Measurement Of Porous Silicon Layer (P-Type) Using Photo-Acoustic Technique

    Mohammed Jabbar Hussein, W. Mahmood Mat Yunus, Halimah Mohamed Kamari, Azmi Zakaria

    Paper ID II-ICTAEECEMAL-01055-1375 · Pages 28-31

    Abstract

    Thermal diffusivity for porous silicon p-type was measured using the photoacoustic technique. The porous silicon samples were prepared under the current densities of 10 to 30 mA/cm2 whilst the etching time ranged from 20 to 80 min. The thermal diffusivity of the porous silicon was obtained by graph fitting. Findings from measurement showed that the thermal diffusivity decreased with increasing etching time and current densities.

    Keywords-Etching Time, Thermal Diffusivity, Current Densities, Porous Silicon, Photoacoustic

    Download PDF
  6. Non Linear Simulation Aircraft Behaviour Simulink

    Ahmad Eshtiwey Alaian, Bambang Basuno, Zamri Bin Omar

    Paper ID II-MAPEMAL-03055-1506 · Pages 32-35

    Abstract

    Download PDF
  7. Effect Of Composite Wrappingon Crashworthiness

    Muhammad Izani Sahak, Muhammad Ahmad Kamal

    Paper ID II-MAPEMAL-03055-1516 · Pages 36-39

    Abstract

    Crashworthiness is the ability of a structure to protect its occupants during an impact. Depending on the nature of the impact and the vehicle involved, different criteria are used to determine the crashworthiness of the structure. The combination of metal and composite layers is known to displays plastics deformation and failure mode composite layered. The capable of structures to absorb large amount of energy are great interest in an effort to reduce the impact of collision. In this experimental study, the crashworthiness parameter of composite wrapped mild steel tubes when subjected to axial compression will be investigate. The efficiency is measured in term of the absorption performance that is higher in hybrid composites than in metallic and composite structures alone. Much of the working assessing the energy absorbing capability of composite materials and structures under compressive loading has been to a greater extent restricted to axis metric tubes. Therefore, it will contribute knowledge on how to develop a stable or controlled crushing response of hybrid composite material tubes under sustained axial loading.

    Keywords: Axial Compression, Circular and Square Tube, Energy Absorption, Fiber Metal Laminated Mild Steel.

    Download PDF
  8. Low Temperature Condition For Nio Nanoparticles Preparation Via Sol‐Gel Method

    P.V. Chai, Muneer. M. Ba‐Abbad, Y.H. Teow, A.W. Mohammad

    Paper ID IRES-ICETIKLMPR-02055-51 · Pages 40-44

    Abstract

    Download PDF
  9. Numerical Analysis Of Flameless Combustion Using The Torus Combustion Chamber

    Seong Shin Ong, Yongson Ooi, Kia Wai Liew, Dirk Rilling

    Paper ID IRES-ICETIKLMPR-02055-155 · Pages 45-49

    Abstract

    The main objective of this research is to design and analyze a low polluting combustion system, in particular the most hazard and common polluting substance, nitric oxide (NOx). In order to reduce the NOx formation through high temperature combustion, flameless oxidation is the solution. The peak combustion temperature is lowered through flameless oxidation and hence suppresses the formation of NOx. The flameless oxidation or combustion is achieved by inducing large amount of exhaust gases recirculation. This project is focused on designing a new combustion chamber to specially cater to optimizing the performance for flameless combustion using various types of fuels, including the biofuel. A torus shaped of combustion chamber is designed and tested on various fuels in both flame and flameless combustion mode. Using the commercialized numerical code; various numerical models were produced to give the insight of the flameless combustion. The numerical models are validated with the experimental data. From both experimental setup and numerical models, the data shows that the thermal NOx formation has been greatly suppressed with the large amount of recirculation due to the torus shaped combustion chamber.

    Index Terms- Flameless combustion, NOx emissions, Torus chamber, Numerical analysis.

    Download PDF
  10. Development Of Three Year Old Nigerian Numerical Child Dummy Head And Validation In Frontal Impact

    I. A. Rafukka, B. B. Sahari, A. A. Nuraini, A. Manohar

    Paper ID IRES-ICETIKLMPR-02055-225 · Pages 50-54

    Abstract

    Download PDF
  11. Doing Business In Economic Crisis

    Salem Alrhaimi, Mohamed Ibrahim Mugableh

    Paper ID IRES-ICSSHKLMPR-03055-225 · Pages 55-57

    Abstract

    This paper seeks to encourage potential and existingentrepreneursto do business, even in economic crisis and global recession. The global economic crisis strongly affected less developed areas, especially small entrepreneurs in these areas. In such conditions there is not much space left for successful entrepreneurship, entrepreneurs are forced to search new opportunities, and to do businesses with higher risks. They must have a modern approach to entrepreneurship, which tries to discover new opportunities in an innovative way. The paper shows that crisis and recession can provide new opportunities that need to be detected at the right time Competitive advantage may be gainedifthe entrepreneur is able to offer something valuable and important to the market, and if it differs from the competition in a way that offers better quality. In addition, there must be many other sources of competitive advantages which should support the main source of competitive value. The aim of the paper is to help entrepreneurs to find sources of competitive advantage in time of economic crises.

    Key words-Doing Business; Economic Crisis; Competitive Advantage.

    Download PDF
  12. FPGA Implementation For Real Time Sobel Edge Detector Block Using 3-Line Buffers

    Ronnie O. Serfa Juan, Chan Su Park, Hi Seok Kim, Hyeong Woo Cha

    Paper ID SP-ICIEEEKLMPR-11045-227 · Pages 58-63

    Abstract

    Download PDF
  13. Structural Defect Detector Based On Very Low Power, Low Cost, Less Complexity, And Wireless Communication Method

    Ahmad H. Sabry, Yasir Mahmood Alkubaisi, Iman Ahmed

    Paper ID SP-ICRACEKLUMPUR-12045-225 · Pages 64-70

    Abstract

    Download PDF