London, United Kingdom, 20-04-2015
ISBN 978-93-82702-97-9
South African cities are predominantly maintained and developed in the form of conventional infrastructure and the associated conventional funding thereof. The promotion of sustainable practices in urban development is not necessarily coupled with alternative or sustainable forms of financing. Although the public sector will always remain the key initiator behind infrastructure development, various mechanisms of financing, along with applicable financing partners and the basis of investment, will be required so as to address future sustainable cities. This paper proposes a framework to investigate the financing of sustainable cities in South Africa.
Keywords- Financing, framework, sustainable cities
This paper presents the development of an information system for Decision Support System (DSS) for optimal Computer Aided Design (CAD) system configuration. The genetic algorithm solution has been considered. The architecture of a decision support system is represented.
Index Terms- CAD, CAD system configuration, decision making, methods of optimization, genetic algorithm.
Efficient small scale axial air turbine is one of the proposed solutions for improving the overall efficiency of energy recovery cycles based on renewable energy sources. Turbine design requires an intensive CFD simulation and design optimization to identify optimal blade profile for maximum efficiency. Axial turbine rotor optimization was carried out usingdifferent optimization techniques available in ANSYS CFX. The highest rotor efficiency was accomplished using Multiobjective optimization algorithm (MOGA) with highest turbine efficiency of87.78% was achieved.
Keywords- Axial Turbine, Optimization, CFX, Efficiency
A series of friction measurements were performed for compliant contact under starved lubrication. Three conditions of initial preparations of the lubrication condition were examined: heavy lubrication, light lubrication, and dry friction. The effects due to surface roughness, entrance angle, contact pressure, and sliding speed were also measured and discussed. The Stribeck diagrams formed with the measured data indicate significant influence on friction performance due to the starting amount of lubricant applied on the friction interface for starved EHL, even when the operating conditions are the same.
Index Terms- Elastomer, damper, initial condition, soft contacts
A batch processor is capable of processing several jobs at the same time up to their capacities. When a batch processor completes its job and there are jobs waiting in the queue, a loading decision should be made whether it starts processing a batch of jobs immediately or waits for more jobs to arrive before initiating a batch service. This paper addresses loading decision problem for batch processors with the objective of tardiness minimization. We presents a loading procedure where due-date information of the jobs are considered. Simulation experiments are performed to validate the performance of the proposed model.
Index Terms- batch processor, loading decision, batching, tardiness minimization.
Titanium alloys are one of the most difficult materials to machine because of their low thermal conductivity and high chemical reactivity which leads to high cutting temperatures and tool wear. This paper focuses on machinability assessment of titanium alloy Ti6Al4V under 3 different heat treatment conditions using turning operation. The experiments were planned using Taguchi design of experiment approach and using L8 orthogonal array, where cutting speed, feed and depth of cut were varied on 2 levels. The machinability was measured in terms of cutting forces and surface finish of the machined workpiece. The chip mechanism and chip microstructural study was carried out to establish a direct relationship between machinability and heat treatment processes.
Index Terms- Chip Mechanism, Chip Microstructure, Heat Treatment, Ti6Al4V
Titanium and its alloys are considered difficult-to-machine materials due to several factors such as very high cutting temperature induced at the cutting edge during machining, its high strength at elevated temperature and strong chemical reactivity with many cutting tools. The machinability of titanium alloys was considerably influenced by the heat treatment conditions and its subsequent microstructure produced. A beta solution treatment process (BSTA) produces lamellar microstructure and mainly carried out to improve the fatigue properties of Ti6Al4V. This lamellar microstructure which is coarse produces high shear stress and in consequence produces high cutting forces and cutting temperature which leads to poor machinability. Cryogenic Machining using LN2 was carried out on beta solution treated Ti6Al4V using Taguchi design of experiment approach with L8 orthogonal array, where 3 factors viz. cutting speed, feed rate and depth of cut were varied on 2 levels. During cryogenic machining, LN2 was supplied with high pressure to the cutting zone which receives an effective cooling as well as the chip breaking takes place. The machinability was measured in terms of cutting forces and surface finish of the machined work piece. The chip mechanism study was also carried out to establish a direct relationship between machinability and heat treatment process.
Index Terms- Ti6Al4V, Beta solution treatment, Cryogenic, Taguchi, Chip Microstructure, Chip Mechanism
The Cryogen based Energy Storage (CES) technology which uses liquid air/nitrogen as an energy carrier has attracted lots of attention recently due to its higher energy density compared to other thermal energy storage technologies. This stored liquid can then be expanded through a Rankine cycle to convert the stored energy to work. Although higher ideal cycle efficiencies can be achieved with this configuration, the effect of the real turbine efficiency can be significant on the overall cycle efficiency. Therefore, it is important to predict the performance of the turbine at cycle operating conditions different from the turbine design operating point. In this work the Mean line method and ANSYS CFD were used to develop a small scale cryogen turbine and predict its performance at different operating conditions using Nitrogen as the working fluid. Results showed that the inlet pressure has the highest impact on the turbine performance as it shifts from the design operating point.
Keywords- Nitrogen ,Cryogenic Axial Turbo-Expander, mean line , CDF Analysis
This is a desceiptive community based cross sectional study conducted in unmarried women their ages rang from 15 to 45 years old. Dysmenorrhea is medical term for menstrual cramps menstrual cramps are sharp pain in woman lower abdomen that occure when menstrual period begins and it is most common gynecological complaint among adolescent girls. The general objective of this research is to assess the effect life style and the occurrence of dysmenorrhea among unmarried women the study is done at sudan khartoum state. The study found 60% of unmarried women complain of painfull cramps every month, the highest age group between 15 and 20 years old. 68.7% practice exercise without complaining of dysmenorrhea which is a good sign that exercise had a great effect on dysmenorrhea.
Index terms- Dysmenorrhea, Exercise prctice, Smoking, Unmarried women.
The increment thickness of intima-media thickness (IMT) which involves the changes of diameter of the carotid artery is one of the early symptoms of the atherosclerosis lesion. The manual measurement of arterial diameter is time consuming and lack of reproducibility. Thus, this study reports the automatic approach to find the arterial diameter behavior for different gender, and body mass index (BMI) categories, focus on tracked region. BMI category is divided into underweight, normal, and overweight categories. Canny edge detection is employed to the B-mode image to extract the important information to be deal as the carotid wall boundary. The result shows the significant difference of arterial diameter between male and female groups which is 2.5% difference. In addition, the significant result of differences of arterial diameter for BMI category is the decreasing of arterial diameter proportional to the BMI.
Index Terms- B-mode Ultrasound Image, carotid artery diameter, canny edge detection, body mass index.
A numerical and experimental studies of passive micro drops production have been presented. This paper focuses on the modeling of micro-oscillators systems which are composed by passive amplifier without moving part. The micro-system modeling is based on geometrical oscillators form. An asymmetric micro-oscillator design that is based on a bistable fluidic amplifier is proposed by .Foster and khelfaoui. The characteristic size of the channels is generally about 35 microns of depth. The numerical results indicate that the production and manipulation of microdrops are possible with passive device within a typical oscillators chamber of 2.25 mm diameter and 0.20 mm length when the Reynolds number is Re = 490. The novel micro drops method that is presented in this study provides a simple solution about the production of microdrops problems in micro system. We undertake an experimental step. The first part is based on the realisation of sample oscillator; the second part is consisted of visualization, production and manipulation of microdrops.
Keywords- modelling, miscible, micro drops, production, oscillator sample, capillary.