← All proceedings

48TH THE IIER INTERNATIONAL CONFERENCE

Proceedings cover: 48TH THE IIER INTERNATIONAL CONFERENCE

Spain, Barcelona 11-12-2015

ISBN 978-93-85832-61-1

11 papers

  1. Cybercrime Fighting Readiness Evaluation Using Analytic Hierarchy Process

    Mohammed Otair, Aiman Al-Refaei

    Paper ID II-ABMITSPN-11125-2930 · Pages 1-6

    Abstract

    Since the first cybercrime was recorded in 1820 and with the fast growth of the Internet usage and computerized systems, it has become critical to know what the affect that cybercrimes may cause. Organizations have to estimate their readiness to fight such kind of crimes by determining the main significant factors that may affect their readiness level. Upon that they work on enhancing the low-weighted factors. This paper provides a new approach of evaluation method to Cybercrimes fighting readiness using Analytical Hierarchy Process (AHP). The major idea of this paper lies in showing how to identify the readiness of an organization to fight Cybercrimes and how to determine the critical factors that affect this readiness, and the weights (relative importance) of the factors for the goal (Cybercrime fighting) and for each other hence reaching the percentage of readiness level of Cybercrime fighting for an organization. It is important to note that the factors are provided by the organization and depend on the setup that the organization uses to reduce the potential risk that may come from cybercrimes. Finally, to clarify the proposed idea and as a proof of concept, a case study is illustrated in the paper. The paper takes the Royal Jordanian Airlines in particular the Information Technology department as a case study showing details and results so as to arrive at conclusions.

    Keywords- Cybercrime, AHP, Decision Making, and Fighting Readiness.

    Download PDF
  2. Effects Of Reinforced Materials On Mechanical Properties Of 3d Composite Structure

    Hamed Ghorbanpoor, Macid Nurbas, Huseyin Avci

    Paper ID II-CBESPN-11125-2947 · Pages 7-10

    Abstract

    Download PDF
  3. Pulser For Piezoelectrics Transducers Used In Non-Destructive Testing

    Eng. Paul ion, Eng. Dan Alexandru Stoichescu

    Paper ID II-ICRIETSPN-11125-03 · Pages 11-14

    Abstract

    In order to get, at the ultrasonic receiver input, a clear echo pulse, it is very important to apply on the transducer a short high amplitude pulse (hundreds of volts). The pulse frequency is low enough to allow the reception and processing of the informations received from the analysed material between two adjacent pulses, but high enough to ensure an integral control of the material. The piezoceramic disc chattering amplitude is maximum if the pulse frequency spectrum is centered on a frequency fc equal to the piezoceramic disc frequency. Ideally, the excitation pulse falling edge must be 10% to 30% lower than λ/4, where λ is the wavelength corresponding to the piezoelectric disc central frequency. The dimensions of the sonic field surface crossed by the controlled piece, the incidence angle of the ultrasonic beam on the piece- environment interface are essential elements ensuring the efficienty of the ultrasonic inspection method. In the paper a high bandwidth pulse generator for ultrasonic transducer excitation is presented. The generated signal frequency may vary between 2MHz and 17MHz, the pulses falling edge is lower than 10ns, their amplitude is U=300V (a slew rate of 30V/ns); VMOS transistors and bipolar transistors are used as switching devices.

    Index Terms- Non-Destructive Testing, pulser,ultrasounds

    Download PDF
  4. Green Daylit Industry For Dhaka: An Evaluation Of Integrated Skylights And Solar Panels For Rmg Factory Buildings

    Md Ashikur Rahman Joarder, Md Nahid Iqbal

    Paper ID II-ICRIETSPN-11125-2651 · Pages 15-20

    Abstract

    Download PDF
  5. Understanding The Effects Of Residual Gas Trapping On Combustion Characteristics, Engine Performance And Operating Range In A Hcci Engine

    Ahmet Uyumaza, Can Cinarb

    Paper ID II-ICRIETSPN-11125-2736 · Pages 21-27

    Abstract

    In this study, experimental investigation was performed in order to determine the effects of residual gas fraction (RGF) using low lift cams in a single cylinder, four stroke gasoline HCCI engine. For this purpose, the test engine was equipped with variable valve lift mechanism including intake and exhaust cam with 5.5 and 3.5 mm valve lift. The experiments have been carried out to understand the effects of RGF with three pairs of cam mechanisms (IN 5.5-EX 5.5, IN 5.5-EX 3.5 and IN 3.5-EX 3.5). The test results showed the test engine was run between 800-1900 rpm at different air fuel ratios and inlet air temperatures on HCCI mode. It was found that IN 5.5-EX 3.5 cam mechanism presented the more reasonable results among the other cam mechanisms and HCCI operating range was extended when misfiring and knocking boundaries were examined. Higher RGF was obtained with IN 3.5-EX 3.5 cam mechanism. Indicated thermal efficiency was obtained 26.67 % for IN 3.5 EX 3.5 whereas 27.5 % for IN 5.5-EX 3.5 at stoichiometric ratio and 1000 rpm engine speed. As a result, it was seen that combustion phasing could be controlled with RGF and HCCI operating range could be extended trapping exhaust gases in the combustion chamber.

    Index Terms- HCCI, Combustion, Operating range, Residual gas fraction, Performance

    Download PDF
  6. Use Of Energy Function To Assess Voltage Stability Of A Four-Bus Power System With A Svc

    Ahmet Cifci, Yilmaz Uyaroglu

    Paper ID II-ICRIETSPN-11125-2737 · Pages 28-33

    Abstract

    Electric power systems are more heavily loaded than ever before. That makes power systems operate in critical position at the boundary of voltage stability region. This paper discusses the effects of a static VAr compensator (SVC) to improve voltage stability of a four-bus power system. Energy function analysis by using the variable gradient method is employed. The numerical simulations demonstrate that the use of SVC improves voltage stability.

    Index Terms- Energy function, four-bus power system, static VAr compensator, voltage stability.

    Download PDF
  7. Design And Implementation Of RFID Reader For Animal Tags

    Huseyin Harmanci, Hakan Isik

    Paper ID II-ICRIETSPN-11125-2856 · Pages 34-37

    Abstract

    In this study, we designed of handheld RFID reader for ISO 11784 & 11785 standards that regulate the wireless communication protocol of animal identification with RFID technology. RFID ear tags are preferred by farmers in a lot of animal farms. Because they look the same as traditional ear tags, so farmers can use them in the same way. In the hardware side, the reader has a microcontroller and EM4095 that is a CMOS integrated transceiver circuit. We used it for reading 125 kHz RFID tags that have Manchester & bi-phase encoding ICs. The difference of this study is that we calculated the value of components for 134.2 kHz and developed new software for ISO 11784 & ISO 11785 code structure.

    Key words- EM4095, ISO 11784 & ISO 11785 protocol, RFID Reader, 134.2 kHz Animal RFID.

    Download PDF
  8. Investigation Of Bowel Perforation Detection Using Fluorescent Chlorophyll Derivatives

    Jung Hyun Han, Young Goun Jo, Jung Chul Kim, Yong-Chul Kim, In-Wook Hwang

    Paper ID II-RAMSSPN-11125-2858 · Pages 38-42

    Abstract

    Download PDF
  9. Representing Bharat Mata In Popular Hindi Films: A Socio-Historical Study Of Nationalist Politics Of Death

    Souvik Mondal

    Paper ID II-SSESPN-12125-2684 · Pages 43-50

    Abstract

    Download PDF
  10. Subsurface Flow Constructed Wetland For Treatment Of Wastewater Of Small Communities In Turkey

    Merve Mahmutoglu, Mustafa Sait Yazgan

    Paper ID II-NSESPN-12115-01 · Pages 51-55

    Abstract

    Download PDF
  11. Reliable Intelligent Fault Diagnosis System For Electrical Machines

    Bouchareb, A. Bentounsi, A. Lebaroud

    Paper ID II-ICRIETSPN-11125-02 · Pages 56-60

    Abstract

    Download PDF